
Most homeowners discover the problem the same way. A water truck delivery runs out early, the bill jumps, or a damp patch appears where there was none before. The tank is the obvious suspect, and sometimes rightly so. But just as often the real cause is a float valve sending water down the overflow, or a pipe under the yard that has nothing to do with the tank.
Do not dig or break anything until you know. This guide gives you the warning signs, a simple test you can do with a pencil and a ruler, and a clear way to act on the result.
Signs of a leaking water tank
One sign alone proves little. If you recognise more than one, start testing.
- Water running out sooner with the same number of people at home.
- A higher water bill, or more truck deliveries with no change in your use.
- A pump that runs too often, or cycles on and off with every tap closed.
- Damp around the tank, such as wet soil, paving darker than the rest of the yard, or moist ground in summer.
- Grass growing where nobody waters, or insects gathering at one spot.
- White salt deposits or rust stains on the tank or a neighbouring wall.
- Sinking paving or new cracks in a wall close to the tank.
- Cloudy or odd-tasting water, which usually points to something getting in and not water getting out.
First question tank, plumbing or float valve?
Before blaming the tank, remember your water passes through several stages from the mains or truck into the tank, from the tank to the pump, and from the pump to the house. A loss at any stage looks the same from the outside. Check these four suspects in order.
- Float valve and overflow. A faulty float lets water keep coming in and straight out through the overflow. A lot of water disappears from a perfectly sound tank.
- The incoming line. A broken buried pipe between the meter and the tank spins the meter while the tank fills more slowly than it should.
- The outgoing line and pump. A leak after the tank, on the roof or in the yard, or a toilet cistern quietly running, will drain water slowly.
- The tank itself. A wall, the floor or the point where a pipe passes through.
If you are not sure how your pipework runs, read tank plumbing connections and the tank pump guide before you start.
The overnight level test, step by step
This is the most useful check in the article, and it costs only a night without drawing from the tank. Pick a time when the house can manage without it, or set some water aside first.
- Fill the tank to a clear level, below the overflow so nothing escapes that way.
- Close the inlet valve at the tank and make sure the float is not letting anything in.
- Close the outlet valve and switch off the pump at the power so it cannot draw any water.
- Mark the level. Lower a clean stick or ruler through the hatch until it touches the water, and record the distance from the hatch rim. You can also tape a mark on the wall if you can reach it without climbing in.
- Note the time and leave it for a full night without opening anything.
- Measure from the same point in the same way, and write down the difference.
Evaporation inside a closed tank will not cause any meaningful drop in one night. If the level falls clearly, the water has gone somewhere.
Turning a level drop into litres
A centimetre does not sound like much, but it means different things in different tanks. You can estimate it by dividing capacity by height, and here is that sum done for our sizes.
| Tank size | Capacity | Height | About 1 cm equals |
|---|---|---|---|
| 14 m³ | 14,000 litres | 2.80 m | 50 litres |
| 22 m³ long | 22,000 litres | 3.30 m | 67 litres |
| 22 m³ square | 22,000 litres | 3.00 m | 73 litres |
| 24 m³ | 24,000 litres | 2.90 m | 83 litres |
| 28 m³ | 28,000 litres | 2.90 m | 97 litres |
| 29 m³ long | 29,000 litres | 3.30 m | 88 litres |
| 29 m³ wide | 29,000 litres | 3.30 m | 88 litres |
Say a 24 m³ tank falls 5 cm overnight. That is about 415 litres. At 250 litres per person per day, it is more than a day and a half of water for one person, gone in a single night with nobody using anything. These numbers are approximate because a stick will never be perfectly precise, but they tell you how serious things are. For a comparison with your normal consumption, try the tank size calculator.
Reading the result
| Result | Likely cause | Next step |
|---|---|---|
| Level unchanged | Tank probably sound | Look at the incoming line, float and house plumbing |
| Very slight drop | Measuring error or a valve not fully shut | Repeat for a second night |
| Clear drop | Leak in the tank, its openings or the outlet valve | Run the level-finding test below |
| Level rose | Valve or float passing water, or water entering from the ground | Check the valves, then the site, and stop drinking it |
Tests that narrow down the location
The level-finding test
If the level fell, let it keep falling with no filling and no use, and keep measuring. It will often stop at a certain height, which gives you a rough location for the leak. If it stops level with a pipe, start there. If it stops at a line on the wall, there is probably a crack at that height. If it carries on down to near the bottom, look at the floor or the lower corners.
The meter test
If your tank is fed from the mains, close all taps and the valve into the tank, then watch the meter. A meter that keeps moving with no use means a leak between the meter and the tank, which is a plumbing job and nothing to do with the tank. Film it and call a plumber.
The float and overflow test
Lift the hatch once the tank is full. If you hear water still coming in or see the overflow pipe dripping, the float needs adjusting or replacing. This is one of the simplest and cheapest causes to fix.
The after-the-pump test
Open the outlet valve and run the pump with every tap in the house closed. If the pump keeps cutting in and out, something in the house is losing water. Start with toilet cisterns and any roof tanks.
Inspecting inside the tank safely
If the tests point to the tank itself, it needs emptying and inspecting from inside. Safety matters most at this stage. A tank is a confined space, so never go in alone.
- Isolate the pump's power first, and keep someone outside the tank the whole time.
- Open all covers and let the tank air out before anyone goes in.
- Never run a generator or petrol engine inside the tank or at its opening.
- If you feel dizzy or short of breath, get out immediately. If in doubt, leave this to a specialist team.
- On a site with high groundwater, do not fully empty the tank before reading our guide to tanks in high groundwater.
Once the surfaces are dry, check these places in order.
- The corners where the walls meet the floor.
- Around the inlet and outlet pipes.
- Peeling in the internal lining, or blisters beneath it.
- Crack lines in the walls, especially with salt deposits on them.
- Rust stains or exposed steel.
Take the chance to clean the tank before refilling, following our tank cleaning guide. Use tools that will not scratch the lining, for the reasons set out in our article on bitumen and chemical waterproofing.
What to do in each case
| What you found | Action | Who does it |
|---|---|---|
| Float or valve fault | Adjust or replace | Plumber |
| Pipe under the yard | Trace the route and repair the break | Plumber, with leak detection if needed |
| Around a pipe in the tank wall | Reseal the opening and the waterproofing around it | Tank specialist |
| Peeling lining with no crack | Prepare the surface and reapply the lining | Waterproofing specialist, using a water tank product |
| Leaking crack | Have it assessed before any patching | Concrete specialist or engineer |
| Rusty steel or many cracks | Consider replacing and not repairing | Engineer and tank supplier |
When it becomes urgent
- Damp at the building's foundations or sinking ground. Lower the level or empty the tank if the site allows, and call an engineer.
- Cloudy water or a sewage smell. Stop using the water for drinking and cooking, and investigate the source first.
- A crack visibly growing. Keep people away and reduce the pressure by lowering the water.
Common mistakes that make leaks worse
- Cement plaster over a wet crack. It hides the problem without closing the water's path.
- Waterproofing paint over a wet surface. It will not bond, and it soon peels.
- Ordinary waterproofing products in a drinking tank. Anything inside the tank must be made for water tanks.
- Adding dye or chemicals to trace the leak. Nothing goes into a tank you drink from.
- Waiting because the loss seems small. A small daily loss keeps soil wet and eventually carries moisture to the steel.
- Digging before testing. You excavate around the tank and it turns out to be the float. It happens more than you would think.
Repair or replace?
Three questions help. Is the problem at one spot or several? Are the concrete and steel sound? Has the same spot been repaired before and failed again? One spot in sound concrete makes repair sensible. Repeated repairs, rust, and cracks across several walls usually mean replacement is the decision you will not regret. Our list of signs a tank needs replacing goes through it.
If your old tank was cast on site and you are considering a change, compare precast and cast-in-place tanks and look at our precast concrete tanks. Still weighing other materials? See concrete vs fibreglass.
Lowering the risk from the start
- Support pipes properly near the tank so they do not strain the point where they enter.
- Do not drill the tank wall or fix anything to it after installation.
- Keep irrigation and yard-washing water away from the hatch.
- Do not drive or park heavy loads over an underground tank unless that has been designed for.
- Take a level reading from time to time. Once you know what is normal, you will spot what is not.
- Choose a proper base and clean backfill, as our site preparation guide explains.
If your tank is ours, or you want to replace yours
Our tanks carry a 10-year warranty on manufacturing and installation, covering cracks and leaks. If you notice something, note the dates and level readings, take photos of the area, and send them to us on WhatsApp with your location. That shortens the conversation considerably.
If your current tank has reached the end of the road, work out your capacity with the tank size guide and look over our tank sizes. Send us the location and site photos, and we will reply with a free written quote and a date, with an official tax invoice. We serve all regions of Saudi Arabia, and installation usually takes one day once the site is ready.
