Concrete Tank
  1. Home
  2. Articles
  3. How to Match a Pump to a Ground Water Tank

Article

How to Match a Pump to a Ground Water Tank

A ground tank stores the water, but the pump decides how it reaches you. Pick one by guesswork and you get weak showers or a burnt motor. Here is how to work it out before you buy.

Updated · Concrete Tank team

Water pump connected to a buried concrete tank through suction pipework

Most owners spend weeks choosing a tank and five minutes choosing the pump. They walk into a shop, ask for something strong, and go home with whatever is on the shelf. Then the top floor has poor pressure, or the pump keeps kicking on and off all night.

The decision is simpler than it looks. An underground tank has its floor below the level of the house, so something must lift every litre. If you know three numbers about your home, you can have a sensible conversation with your plumber and judge any recommendation for yourself.

Start with the pump's job

Before talking about brands or motor size, decide what the pump actually has to do. Most homes in the Kingdom use one of two arrangements.

Transfer to a roof tank

The pump draws from the ground tank and lifts water to a smaller tank on the roof. A float in the roof tank tells it when to start and stop, and the house is fed by gravity. The pump only has to reach roof height. Tap pressure depends on how far the roof tank sits above each tap, not on the pump.

Direct pressure to the house

There is no roof tank. The pump pushes water straight into the pipework, usually with a pressure switch and a small pressure vessel so it does not start for every drip. Now the pump must reach the highest outlet and still leave comfortable pressure there. This needs more careful sizing, since any shortfall shows up immediately in the shower.

A third case is common on farms a well pump fills the tank, and a second pump draws from it for irrigation. Those are two different jobs with two different calculations. Our farm water storage guide covers that setup.

Submersible or surface pump?

There is no universal winner. Here is how they compare in practice.

PointSubmersibleSurface
LocationInside the tank, under waterOutside, in a room or box
How it moves waterPushes upwardSucks, then pushes
SpaceNone outsideNeeds a shaded, ventilated spot
NoiseVery quietAudible if near bedrooms
ServiceMust be lifted outEasy to reach
Typical weak pointSediment if set too lowLosing prime through air leaks

Choose a surface pump if you have room beside the tank and want easy access. Choose a submersible for tight plots, or where noise near the majlis or bedrooms would annoy you. If you are still deciding on where the tank goes on a villa plot, plan the pump position at the same time.

Work out the head

Head is how high a pump can push water, written in metres. Measure from the floor of the tank, not from ground level, because the pump still has to work when the water is low.

Our tanks range from 2.80 to 3.30 m tall. Bury a 14 m³ tank and the floor sits close to 2.80 m below ground. With a 29 m³ long tank that grows to about 3.30 m. Those metres count even in a single-storey house.

The sum is total head equals vertical distance from tank floor to highest point, plus friction loss in the pipes, plus the pressure you want at the tap if there is no roof tank. A handy reference is that every 10 m of height is roughly 1 bar of pressure.

A worked example

Take a villa with a buried 22 m³ long tank, 3.30 m tall, and a roof tank about 10 m above ground. In the worst case, water climbs 13.30 m. Add friction loss, which grows with every metre of pipe and every elbow. Your plumber can estimate that from the actual run and pipe diameter. Then read the manufacturer's pump curve at that head. Flow drops as head rises, so a pump advertised with a large maximum figure may deliver very little at your real height.

These numbers only illustrate the method. Your own house has its own distances.

Work out the flow

Flow is how much water the pump delivers, usually in litres per minute or m³ per hour. It answers a daily question can a shower, a washing machine and the kitchen all run together?

With a roof tank, this matters less. The roof tank covers the peaks and the pump refills it at its own pace. As an example, if the roof tank holds 2,000 litres and the pump gives 40 litres per minute at your head, it fills in about 50 minutes. Run the same sum with your own numbers.

With direct pressure, the pump must cover your busiest moment alone. Think of the morning rush. In apartment buildings the calculation spans every flat and floor, and that is work for an engineer or an experienced installer, not a guess. The building water storage guide gives you the wider picture.

Does tank size change the pump?

Capacity does not set pump size. A 14 m³ and a 29 m³ wide tank could serve the same house with the same pump. What changes is how long your water lasts. A family of eight at 250 litres per person uses 2,000 litres a day, so 14 m³ gives them 7 days and 29 m³ gives them 14.5 days. The tank size calculator runs this for your own household.

Tank height does matter a little. The 22 m³ square tank is 3.00 m tall and the 22 m³ long tank is 3.30 m. Same water, but a 30 cm difference at the lowest suction point. That is minor, unless your surface pump is already close to its suction limit.

The suction limit on surface pumps

A surface pump cannot push water from below. It relies on atmospheric pressure to bring water up the suction line, and that has a natural ceiling. In practice, as the vertical gap grows, suction gets weaker and air problems get worse. So keep the pump close to the tank, and keep the suction line short and straight with as few elbows as you can.

If the pump sits above the water level, fit a foot valve at the end of the suction line to keep it full. If the pump runs but delivers nothing, suspect an air leak at a suction joint before you blame the motor.

Parts that protect the system

  • Level sensor or electric float in the ground tank. Stops the pump before it runs dry.
  • Non-return valve. Stops water falling back through the pump when it stops.
  • Isolation valves before and after the pump. Let you remove it without emptying the tank.
  • Dedicated circuit breaker. Installed by a qualified electrician.
  • Small pressure vessel on direct systems. Reduces the number of starts.

For the pipework itself, including inlet, outlet and overflow, read our guide to tank plumbing connections.

Where to put the pump

Pumps generate heat, so give yours shade and airflow. Summer sun across most of the Kingdom is hard on motors and cables. The box or room also needs a drain, so a leaking joint never leaves water sitting around electrics.

In coastal cities such as Jeddah and Dammam, humidity and salty air attack metal parts, so choose a sheltered spot and inspect fittings now and then. Avoid mounting a pump on a bedroom wall, since noise and vibration travel through the structure. A solid base with some vibration damping helps a lot.

Mistakes that kill pumps

  • Drawing from the very bottom of the tank, where sediment collects. Raise the suction point a little and follow our tank cleaning guide.
  • Running the pump while a water truck is filling. The incoming flow stirs up sediment. Switch off and let the water settle, as explained in the water truck filling guide.
  • Skipping dry-run protection, then forgetting the tank is empty.
  • Using a suction pipe narrower than the pump inlet. The pump starves and starts to sound rough.
  • Oversizing without doing the sums, which strains valves, joints and water heaters.
  • Connecting the pump directly to the mains line instead of drawing from the tank.

Buildings and farms

In a building, the top floor pays for every mistake, since those residents are first to lose pressure. Many buildings in Riyadh and other cities pair a large ground tank with a roof tank and a transfer pump. If the ground storage is two precast tanks connected together, use a shared suction line with a valve on each, so service continues during cleaning.

On a farm, distance is the challenge. Long lines lose a lot of pressure, each irrigation type wants something different, and well water may carry sand. If your farm is in Qassim or Al Kharj and runs on a well, have the irrigation installer size the pump for the furthest point, not the nearest.

What to prepare for your installer

  • Tank size, and whether it is buried or above ground on a base.
  • Number of floors and approximate roof height.
  • Whether you have a roof tank.
  • Approximate pipe run from tank to house.
  • What electrical supply is available at the pump location.
  • Household size and your busiest time of day.

Where we come in

We make precast concrete water tanks in our factory in Al Suwaidi, Riyadh, and place them by crane in every region of Saudi Arabia. Each tank has inlet and outlet openings that connect to mains, a water truck, a well or a pump. Tell us early where you plan to put the pump. Send your location and site photos on WhatsApp through our contact page and we will reply with a written quote and a date. Our FAQ answers many of the other common questions.

FAQ

Is a bigger pump always better?
No. An oversized pump cycles on and off too often and strains joints, valves and water heaters. You want a pump that delivers your required flow at your required head, with a modest margin.
Should I choose a submersible or a surface pump?
A surface pump is easier to reach and service but needs a shaded, ventilated spot and a short suction line. A submersible is quiet and takes no outside space, but has to be lifted out for service and must not sit too close to the tank floor.
Do I still need a pump if I have a roof tank?
Yes. Water does not climb from a ground tank by itself, so a transfer pump lifts it to the roof. From there it can feed the house by gravity.
Can one pump serve two connected tanks?
Yes, if both tanks feed a shared suction line with a valve on each. You can then close one tank for cleaning while the pump keeps drawing from the other.
Is the pump included in the tank quote?
Do not assume either way. Ask, and have the written quote state exactly what is included, so you know what to arrange yourself before installation day.
What happens if the pump runs with an empty tank?
Many pumps rely on water for cooling and lubrication, so running dry can destroy them. A level sensor or electric float switch in the ground tank cuts the power when the water gets low.

Ready to order your tank?

Message us on WhatsApp for a final delivered price to your city and an installation date.